RSE CCNA 2 Chapter 10 Quiz Answers 2018 2019

  1. Cisco 2911 Integrated Services Router
  2. Cisco Router 2911 Images
  1. A network administrator is asked to provide the UDI in order to obtain a license for the DATA technology package for the IOS 15.0 on a Cisco 1900 router. What is a UDI?

    • a combination of the product ID and the PAK number
    • a combination of the product ID, the serial number, and the hardware version
    • a combination of the PAK number and the serial number
    • a combination of the serial number and the MAC address of Gi0/0
      Explanation:

      Beginning with IOS 15.0, Cisco modified the process of package licensing. In order to obtain a license for a technology package, the Unique Device Identifier is required along with the Product Activation Key (PAK). The UDI is a combination of the product ID (PID), the serial number (SN), and the hardware version (VID).

  2. What information can be gathered about a neighbor device from the show cdp neighbors detail command that cannot be found with the show cdp neighbors command?

    • the platform that is used by the neighbor
    • the IP address of the neighbor
    • the capabilities of the neighbor
    • the hostname of the neighbor
      Explanation:

      The show cdp neighbors detail command will display the IP address of the neighbor. The show cdp neighbors command displays the platform, capabilities, and name of neighbors, but does not specify IP addresses.

  3. An administrator issued the following commands on router R1:

    R1(config)# logging 192.168.10.2
    R1(config)# logging trap 5

    What conclusion can be drawn from this configuration?

    • The only messages that appear on the syslog server are those with severity level of 4 or lower​.
    • Messages with severity level of 6 or higher appear only on the router console output.
    • The only messages that appear on the syslog server are those with severity level of 5​.
    • Messages with severity level of 5 or higher appear on the router console output and are sent to the syslog server.
      Explanation:

      When these commands are issued, the only messages that appear on the syslog server are those with severity level of 5 or lower. The messages with severity level of 6 or higher appear on the router console output, but do not appear on the syslog server output because the logging trap command limits by severity level the syslog messages that are sent to the syslog server.

  4. A network engineer purchases, installs, and activates a license key on a Cisco 2911 ISR G2 router. What is the next step in the installation process?

    • Reload the router.
    • Register the license with Cisco.
    • Back up the IOS to a TFTP server.
    • Back up the license key stored in flash memory.
      Explanation:

      The installation steps are as follows:

      • purchase the license key
      • use the license accept end user agreement command to accept the EULA
      • use the license boot module command to activate the license
      • reload the router
      • use the show license all command to verify the installation
  5. Fill in the blank. Use a number.
    The syslog protocol uses UDP port 514 to send event notification messages across IP networks to event message collectors.

  6. Which statement describes a syslog server characteristic?​

    • In order for syslog messages to be viewed, a syslog server must be installed on a router in the network.​
    • There are no freeware versions of syslog, only enterprise versions for purchase.​
    • One advantage of viewing syslog messages on a syslog server is the ability to perform detailed searches through the data.
    • The only disadvantage of syslog is the inability to store the messages in a database.​
      Explanation:

      In order for syslog messages to be viewed, a syslog server must be installed on a computer in the network. There are several freeware and shareware versions of syslog, as well as enterprise versions for purchase. Network administrators can easily navigate the large amount of data that is compiled on a syslog server. One advantage of viewing syslog messages on a syslog server is the ability to perform granular searches through the data. A syslog server is a database of informational messages that are received from network devices.

  7. How long is the evaluation license period for Cisco IOS Release 15.0 software packages?

    • 15 days
    • 30 days
    • 60 days
    • 180 days
      Explanation:

      Marco fireplace owner's manual online. Evaluation licenses are good for a 60 day period. After 60 days the evaluation license will automatically change to a Right-To-Use license.

  8. Which technology allows syslog messages to be filtered to different devices based on event importance?​

    • syslog service timestamps​
    • syslog severity levels​
    • syslog facilities​
    • syslog service identifiers​
      Explanation:

      Syslog severity levels provide the ability for an administrator to filter out log messages. Syslog service timestamps provide the capability for log messages to be time-stamped. Syslog facilities and service identifiers provide administrators with an event identification and categorization system.

  9. Which technology via the syslog protocol enhances real-time debugging by displaying the date and time associated with each monitored event?

    • syslog facilities
    • syslog severity levels
    • syslog service timestamps
    • syslog service identifiers
      Explanation:

      Syslog service timestamps provide the ability for log messages to be time-stamped. Syslog severity levels provide the ability for an administrator to filter out log messages. Syslog facilities and service identifiers provide administrators with an event identification and categorization system.

  10. Which Cisco IOS 15 technology package would be needed to implement voice over IP?

    • data9
    • ipbasek9
    • securityk9
    • uck9
      Explanation:

      The uck9 package is for Cisco Unified Communications, which includes support for voice over IP and video.

  11. What is the factory default setting for the configuration register on Cisco routers?

    • 0x2142
    • 0x2102
    • 0x4102
    • 0x4124
      Explanation:

      The default configuration register setting on a Cisco router is 0x2102. This can be seen by executing the command router# show version.

  12. Refer to the exhibit. What two statements describe the NTP status of the router? (Choose two.)

    • The router is serving as an authoritative time source.
    • The router is serving as a time source for the device at 192.168.1.1.
    • The router is attached to a stratum 2 device.
    • The IP address of the time source for the router is 192.168.1.1.
    • The software clock for the router must be configured with the set clock command so that NTP will function properly.
      Explanation:

      The show ntp status command displays information about how NTP is operating on the device. The output shows that the router clock is synchronized with the NTP server with the address of 192.168.1.1. NTP is hierarchical. The router is a stratum 3 device, therefore it’s time source is a stratum 2 device. Authoritative time sources in the NTP system are located at stratum 0.

  13. An administrator wants to send log messages for all severity levels from a router to its console. Which procedure should the administrator follow to accomplish this?

    • The administrator must issue the logging console command on the router.​
    • The messages cannot be viewed on a router console. A syslog server must be installed on a workstation in order to view these messages.
    • The administrator must issue the logging trap 7 command on the router.​
    • The administrator needs to do nothing, because Cisco routers send log messages for all severity levels to the console by default.
      Explanation:

      By default, Cisco routers and switches send log messages for all severity levels to the console.

      I need to schedule a task in Windows Server 2003 that executes this script that deletes files older that n days in the specified folder. The script needs 3 parameters:%1 path to folder where files need to be deleted%2 file names (es.log)%3 number of days @echo off forfiles -p%1 -s -m%2 -d -%3. Microsoft Server 2003 Backup; Using Task Scheduler, the batch file executes properly except for the net use command. Here is the capture from the command window: C:UsersMikeDesktopmixSBS Connectrasdial mixsbsvpn administrator password Connecting to mixsbsvpn. Verifying username and password. Registering your computer on the network. Apr 20, 2011  The last week we setup an internal site for the needs of the company. Although I prefer Linux, the server was running Windows 2003 so we had to go with this. When we finished the setup and the configuration the last thing we had to do was to find a way to backup our data. Schedule server 2003 backup batch file mac To schedule a backup for files or folders, run Windows Server 2003 Backup tool (ntbackup.exe). To run Windows Server 2003 Backup tool (ntbackup.exe), type ntbackup in run dialog box and hit Enter or click Start All Programs Accessories System Tools Backup. By default Windows Server 2003 Backup tool (ntbackup.exe) run in wizard mode. Jan 01, 1980  This batch file will do a full Backup the first time that it is run and an incremental Backup afterwards. Set up a Drive Letter for the Drives. Connect the Drive you are going to use for the Backup.

Cisco 2911 Integrated Services Router

Setup

I need to purchase a SecurityK9 License for our 2911 router. I have never done this, but it seems that you need to have a Cisco smartnet account which I don't have. I am also not sure if this is the license I need since I found this information from Google. Basically I need to be able to use: crypto isakmp, crypto ipsec, crypto map and ip sla.

Cisco Router 2911 Images

A network engineer purchases, installs, and activates a license key on a Cisco 2911 ISR G2 router. What is the next step in the installation process? Reload the router. Register the license with Cisco. Back up the IOS to a TFTP server. Back up the license key stored in flash memory. Hi, i have a 2911 router which has a k9 license. Now i want to upgrade it to sec-k9. I also open a tac request on cisco and they give me the license(.lic) file. Now how to configure the 2911 router so that its license upgraded from k9 to sec-k9. Make offer - USED Cisco CISCO2911-SEC/K9 2911 Security Router Bundle w/SEC license PAK USED Cisco CISCO2911/K9 2911 Router w/3 GE, 4 EHWIC, 2 DSP, 1 SM, 256F/512DRAM £98.31.