06.09.2020
66

Satin doll chart. Din 6930-4: latest: stanzteile aus stahl - sonderteile fuer den fahrzeugbau; masse und zulaessige abweichungen: din en iso 1101: 2017-09: geometrical product specifications (gps) - geometrical tolerancing - tolerances of form, orientation, location and run-out (iso 1101:2017). Title: 4690DAdin6930.pdf Author: Ileana.Stefan Created Date: 4/30/2020 10:33:33 AM.

Cached

Din

Din 6930 Tolerance Table

Stamped steel parts - Part 2: General tolerances

This standard is intended to simplify drawings. It specifies general tolerances on linear and angular dimensions and on coaxiality and symmetry in four accuracy grades which are meant for use and hot stampings made from steel flat products. They shall apply whenever reference is made to this standard on drawings or relevant documents (e. g. in delivery conditions). General tolerances for parts made by fine blanking are not covered in this standard. If, by way of exception, it is intended to apply this standard also to components made from semi-finished products other than flat products, or from materials other than steel, this shall be particularly agreed. This standard shall be applied in conjunction with the specifications given in DIN 6932. DIN 6930-1 is valid for the technical delivery conditions of stamped parts. Regulations for general tolerance in existing drawings are included in clause 5.*This standard is the technical revision of the standard which has been published in 2010-01. This revision primarily includes the update of the normative references and the expansion of the nominal dimension ranges and the tolerances for thickness ranges or for angles on flat stamped parts. This standard is intended to simplify drawings and specifies general tolerances for linear and angular dimensions, concentricity and symmetry in four accuracy levels. They are subdivided into f (fine), m (medium), g (coarse) and sg (very coarse). By selection of a certain accuracy level, the normal workshop accuracy shall be considered. General tolerances according to this standard are used for cold- and warm-formed stamped parts made of flat steel products. They apply if this standard is referred to in drawings or associated documents (for example, terms of delivery). This standard hasbeen prepared by NA 026-00-03 AA 'Stanzteile' ('Stamped parts') of the Springs, Stamped Parts and Moulded Parts Standards Committee (NAFS) at DIN, the German Institute for Standardization e. V. For further information about the NAFS, visit us on the Internet under www.nafs.din.de.

Din 6930 Pdf

Content Provider
Deutsches Institut für Normung [DIN]

Please first log in with a verified email before subscribing to alerts.

Your Alert Profile lists the documents that will be monitored. If the document is revised or amended, you will be notified by email. You may delete a document from your Alert Profile at any time. To add a document to your Profile Alert, search for the document and click “alert me”.

Please first verify your email before subscribing to alerts.

Your Alert Profile lists the documents that will be monitored. If the document is revised or amended, you will be notified by email. You may delete a document from your Alert Profile at any time. To add a document to your Profile Alert, search for the document and click “alert me”.

Already Subscribed to this document.

Din 6930 Standard Pdf

Din

Your Alert Profile lists the documents that will be monitored. If the document is revised or amended, you will be notified by email. You may delete a document from your Alert Profile at any time. To add a document to your Profile Alert, search for the document and click “alert me”.

Documents sold on the ANSI Webstore are in electronic Adobe Acrobat PDF format, however some ISO and IEC standards are available from Amazon in hard copy format.

Din 6930-1 Pdf

Some PDF files are protected by Digital Rights Management (DRM) at the request of the copyright holder. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Some copyright holders may impose other restrictions that limit document printing and copy/paste of documents.

Din 6930 M Pdf Download

Those documents cannot be printed at the request of the copyright holder.